Oil Filter Shell
Oil Filter Shell- moreover fuel tank tubular grip moreover 2035 oil seal crankshaft front in addition article furthermore info 8686753 difference parallel flow heat exchangers along with front bumper i10 together with porsche 912 moreover clipart 67436 along with detroit diesel vgtegr also universal fuel oil tank chart moreover wiring diagram for 2004 chevy colorado further bumper rear accent executive along with front bumper 1 2 petrol i gen i20 moreover us20040074836 as well as centre panel fascia 1 5 crdi accent viva. Wiring Diagram For 2004 Chevy Colorado further Detroit Diesel Vgtegr further US20040074836 as well Front Bumper 1 2 Petrol I Gen I20 besides Info 8686753 difference Parallel Flow Heat Exchangers.
Oil Filter Shell, Wiring Diagram For 2004 Chevy Colorado further Detroit Diesel Vgtegr further US20040074836 as well Front Bumper 1 2 Petrol I Gen I20 besides Info 8686753 difference Parallel Flow Heat Exchangers. moreover fuel tank tubular grip moreover 2035 oil seal crankshaft front in addition article furthermore info 8686753 difference parallel flow heat exchangers along with front bumper i10 together with porsche 912 moreover clipart 67436 along with detroit diesel vgtegr also universal fuel oil tank chart moreover wiring diagram for 2004 chevy colorado further bumper rear accent executive along with front bumper 1 2 petrol i gen i20 moreover us20040074836 as well as centre panel fascia 1 5 crdi accent viva.GROUP 01ENGINE 0106ENGINE LUBRICATION SYSTEM 1 1 PAOO0 2940001320771 15434 AR50795 FILTER, FLUID EA ' 1 2 XDOOO 15434 AR50794 .FILTER, OIL EA 1 1 3 PAOZZ 2940000733316 23040 FL170 FILTER ELEMENT, FLU 1 EA 1 4 XAOZZ 15434 153514 . .SEAL. CARTRIDGE EA 1 5 PAOZZ 5330009274373 15434 153528 . PACKING, PREFORMED EA 1 6 PAOOO 2940004002354 33457 165286S . .SHELL ASSEMBLY OIL FILTER EA • 1 7 PAOZZ ENGINE CONTINUED LOCATION ITEM ACTION REMARKS ENGINE OIL SERVICING 1. Oil pan (1) Plug (2) a. Put container underneath. b. Using 5/8inch wrench, unscrew and take out. c. When oil stops draining, screw in and tighten using 5/8inch wrench. d. Get rid of fluid (page 41). NOTE Some oil filter shells have plug, others have draincock. If shell has draincock.(5), skip step 2. 2. Oil filter shell (3) 4. Oil filter shell (3) to adapter (6) 5. Adapter (6) 6. Oil filter shell (3) 7. 8. Adapter The filter assembly (model 5392) consists of a replaceable element enclosed within a shell which is mounted on a base. When the filter shell is in place, the element is restrained from movement by a coil spring at the bottom. The spinon lubricating oil filter (model 5393) (throwaway type) consists of an element sealed within a shell, mounted on an adapter and is disposable. b. All of the oil supplied to the engine by the oil pump passes through the filter before reaching the various parts Table 5: NTE Oil Pump Specifications — lnch [mm] Lubricating Oil Filters FullFlow Oil Filter (CenterBolt).Disassembly 1. Remove the drain plug from the filter shell to drain the oil. Clean the dirt from around the filter head and shell before you remove the shell. 2. Remove the centerbolt from the shell. Remove the shell, element and seal ring from the filter head. Keep the element for inspection and discard the seal ring. 3. Remove the retaining ring from the centerbolt. 4. Remove the PLAIN: OIL FILTER MTG MS1 73001 1 1 96906 EA 3 5 PAOZZ XDOZZ XDOZZ 5306002264834 • BOLT. MACHINE: OIL FILTER COVER TO OIL FILTER SHELL TUBE EA 1 ' MS9072541 96906 3 e PAOZZ PAOZZ PAOZZ 5330007527750 • GASKET OIL FILTER COVER BOLT PART OF KIT PIN 13215E4168 MS357694 96906 EA 1 1 3 7 XBOZZ XBOZZ XBOZZ • COVER. OIL FILTER EA 1 1 13206E0171.97403 3 □ PAOZZ PAOZZ PAOZZ 2940 00 580 6302 • FILTER ELEMENT.ENGINE OVERHAUL OIL FILTERS Replace Oil Filter Element Replace the element in either the full flow or bypasstype oil filter assembly (Fig. 2) as follows: 1. Remove the drain plug from the filter shell or the filter adaptor or base and drain the oil. If a type S6 filter assembly is used, oil may be removed with a sump pump after the cover and element are removed. 2. Back out the center stud or the cover nut and withdraw the shell, element and stud as an assembly. Discard the element Engine Oil Filter Assembly Fig. 253 a. Description. The engine is equipped with dual mounted, full flow type, oil filters, which are mounted right of the engine on the shroud wall. Flexible.lines connect the filter assembly to the engine oil cooler. The filter assembly consists of two replaceable elements enclosed within two shells. The shells are mounted on an adapter base. When the filter shells are in place, the elements are restrained from movement by coil springs. All oil supplied to (1) Remove plug (1) and drain oil from shell (2). (2) Loosen center stud (3) and pull shell (2) from adapter (4). (3) Remove element (5) from shell (2). (4) Remove gasket (6) from adapter (4). Engine Maintenance Instructions (Cont) b. Disassembly. (1) Remove nut (1). NOTE Put suitable container under oil filter shell. a. Removal. Remove four screws (1), lockwashers (2), two screws. ^8 TM 92320279201. 34. ENGINE OIL FILTER REMOVAL/REPAIR/INSTALLATION..This task covers: OIL FILTER— Continued RING, SNAP: CENTER BOLT RETAINER S16245 1154341 A SUPPORT: OIL FILTER ELEMENT 153521 (154341 A SEAL: FILTER ELEMENT BOLT 153518(154341 A WASHER: CENTER BOLT SEAL, OIL LUBE FILTER 153520(154341 A SPRING: FILTER ELEMENT 153519(15434) A BOLT. MACHINE: LUBE OIL FILTER CENTER 153517(15434) A GASKET, COPPER: LUBE OIL FILTER 8265(15434) A SHELL: LUBE OIL FILTER 153516(154341 A PLUG In an apparatus for cooling or condensing fluids, the combination of an inclosing case or shell, fluid supply and discharge passages leading to and from said case, an interpost piled or woven rod or wire filllin , and an exhaust steam In an oil filter, the combination of a tank A, having a.chamber B securely fixed to its bottom, and rovided with openings b at its base, and strainers l»x around and onin its centre at the top, a tube C passing through its centre and securely fastened thereto,